WCO Explanatory Notes reproduced for reference. © World Customs Organization. Verify against official WCO publication.
84.46 Weaving machines (looms). - For weaving fabrics of a width not exceeding 30 crn 8446.10 - For weaving fabrics of a width exceeding 30 cm, shuttle type : 8446.21 - - Power looms 8446.29 - - Other 8446.30 - For weaving fabrics of a width exceeding 30 cn, shuttleless type This heading covers weaving machines for the production of fabrics by weaving, using textile (including peat fibre) yams or other yarns (e.g., of metal, glass or asbestos). In these machines the warp and weft yarns are interlaced at right angles to form a fabric. r In the simplest weave, the sheet of warp arns fiom the warp beam divides into two groups of alternate yarns, each group being control ed by a harness; these harnesses alternately raise and lower their warp yarns to form an angle (known as the shed) between the two grou s of yarns through which passes the weft yam (in conventional looms carried by a shuttle? which is immediately beaten up against the precedin weft by the reed; the raisin or lowering of the groups of warp yarn is then reversed by the arnesses, entrap ing the weff and forming a new shed for the next line of weft. On ordinary looms up to eight arnesses can be used to vary the order in which the warp yarns are raised and so produce a certain variation in the weave. a g licated weaves. For example, some looms have a More complex looms can execute warp (dobbies, Jacquards, etc.) so as to control a special system for controlling the single warp threads; or special devices can be greater number of groups of warp used to roduce certain special fabrics (leno mechanisms, warp pile (or Terry) attachments, swivel s uttle attachments for brochk work). Other looms have devices for changin the shuttles (or the bobbins in the shuttles), thus introducing wefts of different colours or di erent yarns; Looms often include certain other mechanical or electrical devices (e.g., for replenishin the bobbins in the shuttles when necessary, or for stopping the loom if a warp or weft threa breaks). R # i Most of these special devices may either form an integral art of the loom, or be mounted on an ordinary loom as auxiliary removable attachments; the atter type of attachment is classified here provided it is presented with the loom for which it is intended, but if presented separately it is excluded (generally heading 84.48). f Looms usually produce a flat fabric but there are circular looms which produce a tubular fabric; in these one or more shuttles, moved either mechanically or by electro-magnets, interlace a weft with a vertical series of warp threads arranged in a circle. Different types of looms ma be named according to their type of mechanism or accordin to the type of fabric the pro uce, for example, clobby looms, Jac uard looms, automatic %ox motion looms, shuttle ess looms in which the weft is inserted ei9,er by compressed air or a water jet or by a long needle, or drawn across from a fixed bobbin by a series of projectiles, ribbon looms (e ., bar looms, Zurich looms and drum looms), pile fabric looms, carpet looms including knotte pile carpet looms. r J' d The heading also includes : (1) Hand looms. (2) Looms for weavin clotl: of wire or metallised arn provided they are of the same type as textile weavin koms. such looms must Kave all the essential mechanical parts characteristic o textile v~eavinglooms, i.e., a warp beam, frame harnesses for forming the shed, the mechanism wl ich passes the weft wire or yarn through the shed at right angles and entraps it in the waq yarns and a cloth beam for winding the cloth as lt is produced. f However, the heading excludes machines designed for interlacing wire, by various processes, to form heavy wire grill or netting (see Explanatory Note to heading 84.63). PARTS AND ACCESSORIES Sub'ect to the general previsions regarding the classification of parts (see the General Exp anatory Note to Section XVI), parts and accessories of weaving machines of this heading are classified in heading 84.4 8.
Notes. 1.- This Chapter does not cover : (a) Millstones, grindstones or other articles of Chapter 68; (b) Machinery or appliances (for example, pumps) of ceramic material and ceramic parts of machinery or appliances of any material (Chapter 69); (c) Laboratory glassware (heading 70.17); machinery, appliances or other articles for technical uses or parts thereof, of glass (heading 70.19 or 70.20); (d) Articles of heading 73.21 or 73.22 or similar articles of other base metals (Chapters 74 to 76 or 78 to 81); (e) Vacuum cleaners of heading 85.08; (f) Electro-mechanical domestic appliances of heading 85.09; digital cameras of heading 85.25; (g) Radiators for the articles of Section XVII; or (h) Hand-operated mechanical floor sweepers, not motorised (heading 96.03). 2.- Subject to the operation of Note 3 to Section XVI and subject to Note 11 to this Chapter, a machine or appliance which answers to a description in one or more of the headings 84.01 to 84.24, or heading 84.86 and at the same time to a description in one or more of the headings 84.25 to 84.80 is to be classified under the appropriate heading of the former group or under heading 84.86, as the case may be, and not the latter group. (A) Heading 84.19 does not, however, cover : (i) Germination plant, incubators or brooders (heading 84.36); (ii) Grain dampening machines (heading 84.37); (iii) Diffusing apparatus for sugar juice extraction (heading 84.38); (iv) Machinery for the heat-treatment of textile yarns, fabrics or made up textile articles (heading 84.51); or (v) Machinery, plant or laboratory equipment designed for a mechanical operation, in which a change of temperature, even if necessary, is subsidiary. (B) Heading 84.22 does not cover : (i) Sewing machines for closing bags or similar containers (heading 84.52); or (ii) Office machinery of heading 84.72. (C) Heading 84.24 does not cover : (i) Ink-jet printing machines (heading 84.43); or (ii) Water-jet cutting machines (heading 84.56). 3.- A machine-tool for working any material which answers to a description in heading 84.56 and at the same time to a description in heading 84.57, 84.58, 84.59, 84.60, 84.61, 84.64 or 84.65 is to be classified in heading 84.56. 4.- Heading 84.57 applies only to machine-tools for working metal, other than lathes (including turning centres), which can carry out different types of machining operations either : (a) by automatic tool change from a magazine or the like in conformity with a machining programme (machining centres), (b) by the automatic use, simultaneously or sequentially, of different unit heads working on a fixed position workpiece (unit construction machines, single station), or (c) by the automatic transfer of the workpiece to different unit heads (multi-station transfer machines). 5.- For the purposes of heading 84.62, a “slitting line” for flat products is a processing line composed of an uncoiler, a coil flattener, a slitter and a recoiler. A “cut-to-length line” for flat products is a processing line composed of an uncoiler, a coil flattener, and a shear. 6.- (A) For the purposes of heading 84.71, the expression “automatic data processing machines” means machines capable of : (i) Storing the processing program or programs and at least the data immediately necessary for the execution of the program; (ii) Being freely programmed in accordance with the requirements of the user; (iii) Performing arithmetical computations specified by the user; and (iv) Executing, without human intervention, a processing program which requires them to modify their execution, by logical decision during the processing run. (B) Automatic data processing machines may be in the form of systems consisting of a variable number of separate units. (C) Subject to paragraphs (D) and (E) below, a unit is to be regarded as being part of an automatic data processing system if it meets all of the following conditions : (i) It is of a kind solely or principally used in an automatic data processing system; (ii) It is connectable to the central processing unit either directly or through one or more other units; and (iii) It is able to accept or deliver data in a form (codes or signals) which can be used by the system. Separately presented units of an automatic data processing machine are to be classified in heading 84.71. However, keyboards, X-Y co-ordinate input devices and disk storage units which satisfy the conditions of paragraphs (C) (ii) and (C) (iii) above, are in all cases to be classified as units of heading 84.71. (D) Heading 84.71 does not cover the following when presented separately, even if they meet all of the conditions set forth in Note 6 (C) above : (i) Printers, copying machines, facsimile machines, whether or not combined; (ii) Apparatus for the transmission or reception of voice, images or other data, including apparatus for communication in a wired or wireless network (such as a local or wide area network); (iii) Loudspeakers and microphones; (iv) Television cameras, digital cameras and video camera recorders; (v) Monitors and projectors, not incorporating television reception apparatus. (E) Machines incorporating or working in conjunction with an automatic data processing machine and performing a specific function other than data processing are to be classified in the headings appropriate to their respective functions or, failing that, in residual headings. 7.- Heading 84.82 applies, inter alia, to polished steel balls, the maximum and minimum diameters of which do not differ from the nominal diameter by more than 1 % or by more than 0.05 mm, whichever is less. Other steel balls are to be classified in heading 73.26. 8.- A machine which is used for more than one purpose is, for the purposes of classification, to be treated as if its principal purpose were its sole purpose. Subject to Note 2 to this Chapter and Note 3 to Section XVI, a machine the principal purpose of which is not described in any heading or for which no one purpose is the principal purpose is, unless the context otherwise requires, to be classified in heading 84.79. Heading 84.79 also covers machines for making rope or cable (for example, stranding, twisting or cabling machines) from metal wire, textile yarn or any other material or from a combination of such materials. 9.- For the purposes of heading 84.70, the term “pocket-size” applies only to machines the dimensions of which do not exceed 170 mm x 100 mm x 45 mm. 10.- For the purposes of heading 84.85, the expression “additive manufacturing” (also referred to as 3D printing) means the formation of physical objects, based on a digital model, by the successive addition and layering, and consolidation and solidification, of material (for example, metal, plastics or ceramics). Subject to Note 1 to Section XVI and Note 1 to Chapter 84, machines answering to the description in heading 84.85 are to be classified in that heading and in no other heading of the Nomenclature. 11.- (A) Notes 12 (a) and 12 (b) to Chapter 85 also apply with respect to the expressions “semiconductor devices” and “electronic integrated circuits”, respectively, as used in this Note and in heading 84.86. However, for the purposes of this Note and of heading 84.86, the expression “semiconductor devices” also covers photosensitive semiconductor devices and light-emitting diodes (LED). (B) For the purposes of this Note and of heading 84.86, the expression “manufacture of flat panel displays” covers the fabrication of substrates into a flat panel. It does not cover the manufacture of glass or the assembly of printed circuit boards or other electronic components onto the flat panel. The expression “flat panel display” does not cover cathode-ray tube technology. (C) Heading 84.86 also includes machines and apparatus solely or principally of a kind used for : (i) the manufacture or repair of masks and reticles; (ii) assembling semiconductor devices or electronic integrated circuits; (iii) lifting, handling, loading or unloading of boules, wafers, semiconductor devices, electronic integrated circuits and flat panel displays. (D) Subject to Note 1 to Section XVI and Note 1 to Chapter 84, machines and apparatus answering to the description in heading 84.86 are to be classified in that heading and in no other heading of the Nomenclature. Subheading Notes. 1.- For the purposes of subheading 8465.20, the term “machining centres” applies only to machine-tools for working wood, cork, bone, hard rubber, hard plastics or similar hard materials, which can carry out different types of machining operations by automatic tool change from a magazine or the like in conformity with a machining programme. 2.- For the purposes of subheading 8471.49, the term “systems” means automatic data processing machines whose units satisfy the conditions laid down in Note 6 (C) to Chapter 84 and which comprise at least a central processing unit, one input unit (for example, a keyboard or a scanner), and one output unit (for example, a visual display unit or a printer). 3.- For the purposes of subheading 8481.20, the expression “valves for oleohydraulic or pneumatic transmissions” means valves which are used specifically in the transmission of “fluid power” in a hydraulic or pneumatic system, where the energy source is supplied in the form of pressurised fluids (liquid or gas). These valves may be of any type (for example, pressure-reducing type, check type). Subheading 8481.20 takes precedence over all other subheadings of heading 84.81. 4.- Subheading 8482.40 applies only to bearings with cylindrical rollers of a uniform diameter not exceeding 5 mm and having a length which is at least three times the diameter. The ends of the rollers may be rounded.